 |
| Home |
| Bookmark Page |
| Site Map |
| Car Info |
| Brief Details |
| History |
| Photo Gallery |
| Restoration |
| Interior |
| Engine |
| Suspension |
| Modification |
| Owner Info |
| Meet the Driver |
| Contact Me |
| Shows |
| Credits |
| Useful Info |
| VW Contacts |
| VW Insurance |
| Volksworld Ref |
| General Links |
|
|
Engine Specification
Type 1, 2110cc, Built by John
Maher Racing
Complete parts list
| Crankcase | Dual relief, bored, clearanced, drilled and tapped, etc. | |
| Cylinder Head studs | 8mm gen. VW | |
| Universal case kit | ||
| Crankshaft | 82mm one piece forged, WV journal | |
| Crank gear assembly | Stock VW | |
| Flywheel | 200mm | |
| Conrods | CB Super Rods, 5.400" | |
| Camshaft | Engle FK10 | |
| Cam gear | Aluminium bolt on | |
| Cam plug | ||
| Cam followers | Scat lightweight | |
| Pistons & cylinders | Mahle 90.5mm long stroke | |
| Cylinder spacers | ||
| Teflon buttons | ||
| Cylinder heads | 044 Magnum Plus | |
| Inlet Valves | 42mm stainless steel | |
| Exhaust valves | 37.5mm stainless steel | |
| Valve springs | Dual | |
| Valve spring retainers | Chromoly | |
| Valve spring shims | ||
| Rocker covers & clips | Stock VW | |
| Rocker shafts | Autocraft 1.4:1 | |
| Rocker arms | Autocraft | |
| Tappet screws | Autocraft | |
| Tappet nuts | Autocraft | |
| Lash caps | Gene Berg 369-8 | |
| Rocker pedestal shims | ||
| Pushrods | Gene Berg 3/8" chromoly | |
| Pushrod tubes | Tapered racing tubes and silicone seals | |
| Oil pump | Gene Berg 26mm | |
| Oil pump cover | Gene Berg pressure relief, with take off | |
| Oil filter | Fram HP1 | |
| Oil filter mount | ||
| Oil hose | 2 metres | |
| Oil fittings | ||
| Deep sump | Scat 1.5 litre | |
| Oil cooler | VW doghouse | |
| Oil cooler adapter | ||
| Carburettors | Dellorto 45 DRLA x 2 | |
| Manifolds | supplied with carbs | |
| Fuel pump | Facet fuel pump kit | |
| Fuel pump pedestal | Fuel pump block off | |
| Distributor | Bosch 009 | |
| Ignition module | Ignitor | |
| Distributor clamp | Stock VW | |
| Distributor drive shafts & shims | supplied with crank gear assembly (listed above) | |
| Crankshaft pully | Gene Berg Achiever (stock diamieter) | |
| Crank pully bolt | Gene Berg H.D. | |
| Pulley tinware | ||
| Main bearings | ||
| Conrod bearings | ||
| Cam bearings | 2x sets | |
| Main bearing dowel pins | ||
| Engine gasket kit | ||
| Flywheel oil seal | ||
| Endfloat shims | ||
| Clutch pressure plate | Kennedy Stage 2 | |
| Clutch centre plate | Stock type with solid centre | |
| Release bearing | ||
| Clutch bolt kit | ||
| Flywheel gland nut | Gene Berg 36mm | |
| Oil strainer | ||
| Sump plate | ||
| Domed sump nuts | ||
| Crankcase nut & bolt kit | ||
| Spark plugs | ||
| Ignition leads | Taylor 8mm | |
| Coil | Bosch blue 12v | |
| Exhaust header | Gene Berg 1 5/8" street header | |
| Silencer | 2 1/8'' Magnaflow Turbo Muffler | |
| Alternator pedestal | ||
| Oil filler | Gene Berg oil filler/breather | |
| Dipstick | ||
| Oil | ||
| Cylinder air deflectors |
| Home | Bookmark Page | Site Map | Brief Details | Meet the Driver | Contact Me | | Top |
©2001 - 2007 Craig McKenzie |